最近在往TI Am335x上移植android系统，是android2.3，自己做的板子改了一点，去掉了EVM的cpld，eeprom等，修改了内核，现在移植从串口输出的信息是卡主了，请教各位是怎么回事，本人菜鸟，求指导。
[ 1.324825] omap2_set_init_voltage: unable to set vdd_core
[ 1.335992] omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[ 1.345192] Waiting 1sec before mounting root device...
[ 1.388966] mmc0: new high speed SD card at address 1234
[ 1.395193] mmcblk0: mmc0:1234 SA02G 1.85 GiB
[ 1.402371] mmcblk0: p1 p2 p3
[ 5.849550] kjournald starting. Commit interval 5 seconds
[ 6.098443] EXT3-fs (mmcblk0p2): using internal journal
[ 6.103949] EXT3-fs (mmcblk0p2): recovery complete
[ 6.112826] EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
[ 6.120345] VFS: Mounted root (ext3 filesystem) on device 179:2.
[ 6.127118] Freeing init memory: 208K
[ 6.275318] WL1271: BT Disable
[ 6.398124] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
# [ 10.689071] adb_open
[ 10.697969] warning: `dhcpcd' uses 32-bit capabilities (legacy support in use)
[ 12.577502] gadget: Gadget Zero, version: Cinco de Mayo 2008
[ 12.583581] gadget: zero ready
[ 12.586969] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
[ 12.592569] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 2
[ 12.601273] hub 2-0:1.0: USB hub found
[ 12.605215] hub 2-0:1.0: 1 port detected
[ 12.611683] android_usb: already disabled
[ 12.616818] adb_bind_config
[ 12.873918] Compat-wireless backport release: compat-wireless-2011-07-27
[ 12.881078] Backport based on wl12xx.git v2.6.39-1152-g0c08ddf
[ 14.435563] cfg80211: Calling CRDA to update world regulatory domain
[ 14.986609] cfg80211: World regulatory domain updated:
[ 14.992040] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 15.000889] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.009246] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.017592] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.025936] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.034268] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.543739] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 27.266181] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 35.315270] request_suspend_state: wakeup (3->0) at 35309564422 (2000-01-01 00:00:34.460223314 UTC)
[ 36.232291] request_suspend_state: wakeup (0->0) at 36226586089 (2000-01-01 00:00:35.377243523 UTC)
[ 36.257450] init: untracked pid 130 exited
[ 37.577927] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 41.526016] request_suspend_state: wakeup (0->0) at 41520311299 (2000-01-01 00:00:40.670970399 UTC)
[ 42.598394] init: untracked pid 147 exited
[ 44.106761] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 46.356332] request_suspend_state: wakeup (0->0) at 46350628340 (2000-01-01 00:00:45.501287024 UTC)
[ 47.933459] init: untracked pid 163 exited
[ 49.638517] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 50.907218] request_suspend_state: wakeup (0->0) at 50901513758 (2000-01-01 00:00:50.052171775 UTC)
[ 54.178453] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 56.555105] request_suspend_state: wakeup (0->0) at 56549399842 (2000-01-01 00:00:55.700058776 UTC)
[ 59.737039] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 60.810059] request_suspend_state: wakeup (0->0) at 60804354426 (2000-01-01 00:00:59.955013734 UTC)
[ 64.076343] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 65.918168] request_suspend_state: wakeup (0->0) at 65912463761 (2000-01-01 00:01:05.063122528 UTC)
[ 69.403609] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 71.742579] request_suspend_state: wakeup (0->0) at 71736874134 (2000-01-01 00:01:10.887532568 UTC)
后面这些会一直出
[ 1.324825] omap2_set_init_voltage: unable to set vdd_core
[ 1.335992] omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[ 1.345192] Waiting 1sec before mounting root device...
[ 1.388966] mmc0: new high speed SD card at address 1234
[ 1.395193] mmcblk0: mmc0:1234 SA02G 1.85 GiB
[ 1.402371] mmcblk0: p1 p2 p3
[ 5.849550] kjournald starting. Commit interval 5 seconds
[ 6.098443] EXT3-fs (mmcblk0p2): using internal journal
[ 6.103949] EXT3-fs (mmcblk0p2): recovery complete
[ 6.112826] EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
[ 6.120345] VFS: Mounted root (ext3 filesystem) on device 179:2.
[ 6.127118] Freeing init memory: 208K
[ 6.275318] WL1271: BT Disable
[ 6.398124] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
# [ 10.689071] adb_open
[ 10.697969] warning: `dhcpcd' uses 32-bit capabilities (legacy support in use)
[ 12.577502] gadget: Gadget Zero, version: Cinco de Mayo 2008
[ 12.583581] gadget: zero ready
[ 12.586969] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
[ 12.592569] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 2
[ 12.601273] hub 2-0:1.0: USB hub found
[ 12.605215] hub 2-0:1.0: 1 port detected
[ 12.611683] android_usb: already disabled
[ 12.616818] adb_bind_config
[ 12.873918] Compat-wireless backport release: compat-wireless-2011-07-27
[ 12.881078] Backport based on wl12xx.git v2.6.39-1152-g0c08ddf
[ 14.435563] cfg80211: Calling CRDA to update world regulatory domain
[ 14.986609] cfg80211: World regulatory domain updated:
[ 14.992040] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 15.000889] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.009246] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.017592] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.025936] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.034268] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.543739] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 27.266181] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 35.315270] request_suspend_state: wakeup (3->0) at 35309564422 (2000-01-01 00:00:34.460223314 UTC)
[ 36.232291] request_suspend_state: wakeup (0->0) at 36226586089 (2000-01-01 00:00:35.377243523 UTC)
[ 36.257450] init: untracked pid 130 exited
[ 37.577927] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 41.526016] request_suspend_state: wakeup (0->0) at 41520311299 (2000-01-01 00:00:40.670970399 UTC)
[ 42.598394] init: untracked pid 147 exited
[ 44.106761] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 46.356332] request_suspend_state: wakeup (0->0) at 46350628340 (2000-01-01 00:00:45.501287024 UTC)
[ 47.933459] init: untracked pid 163 exited
[ 49.638517] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 50.907218] request_suspend_state: wakeup (0->0) at 50901513758 (2000-01-01 00:00:50.052171775 UTC)
[ 54.178453] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 56.555105] request_suspend_state: wakeup (0->0) at 56549399842 (2000-01-01 00:00:55.700058776 UTC)
[ 59.737039] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 60.810059] request_suspend_state: wakeup (0->0) at 60804354426 (2000-01-01 00:00:59.955013734 UTC)
[ 64.076343] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 65.918168] request_suspend_state: wakeup (0->0) at 65912463761 (2000-01-01 00:01:05.063122528 UTC)
[ 69.403609] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 71.742579] request_suspend_state: wakeup (0->0) at 71736874134 (2000-01-01 00:01:10.887532568 UTC)
后面这些会一直出
[ 0.085376] Bluetooth: HCI socket layer initialized
[ 0.085393] Bluetooth: L2CAP socket layer initialized
[ 0.085432] Bluetooth: SCO socket layer initialized
[ 0.085648] Switching to clocksource gp timer
[ 0.088710] Switched to NOHz mode on CPU #0
[ 0.095020] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[ 0.095223] musb-hdrc musb-hdrc.0: dma type: pio
[ 0.096002] musb-hdrc musb-hdrc.0: USB OTG mode controller at d080a000 using PIO, IRQ 18
[ 0.096307] musb-hdrc musb-hdrc.1: dma type: pio
[ 0.096959] musb-hdrc musb-hdrc.1: USB OTG mode controller at d080c800 using PIO, IRQ 19
[ 0.097332] NET: Registered protocol family 2
[ 0.097589] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.098020] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.098247] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.098385] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.098404] TCP reno registered
[ 0.098424] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.098460] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.098747] NET: Registered protocol family 1
[ 0.099115] RPC: Registered named UNIX socket transport module.
[ 0.099136] RPC: Registered udp transport module.
[ 0.099151] RPC: Registered tcp transport module.
[ 0.099166] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.099461] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.099545] omap_init_opp_table: no hwmod or odev for iva, [8] cannot add OPPs.
[ 0.256042] Gpio value is :117
[ 0.256631] ashmem: initialized
[ 0.257700] msgmni has been set to 494
[ 0.258773] io scheduler noop registered
[ 0.258793] io scheduler deadline registered
[ 0.258883] io scheduler cfq registered (default)
[ 0.259412] Could not set LED4 to fully on
[ 0.260556] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.261787] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0
[ 0.772618] console [ttyO0] enabled
[ 0.776635] WL1271: BT Enable
[ 0.779964] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1
[ 0.787828] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2
[ 0.795506] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3
[ 0.803262] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4
[ 0.810982] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5
[ 0.825883] brd: module loaded
[ 0.833017] loop: module loaded
[ 0.836630] at24 1-0051: 32768 byte 24c256 EEPROM, writable, 64 bytes/write
[ 0.895700] No daughter card found
[ 0.899332] at24 1-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/write
[ 0.906677] AM335x:EVM Config Without Read E2PROM
[ 1.025701] Board name: A335ABCD
[ 1.029282] Board version: 00AA
[ 1.032585] SKU: SKU#01
[ 1.035320] The board is general purpose EVM in profile 0
[ 1.041017] Found invalid GP EVM revision, falling back to Rev1.1A
[ 1.047863] omap_hsmmc.0: alias fck already exists
[ 1.053510] omap_hsmmc.2: alias fck already exists
[ 1.058918] Configure Bluetooth Enable pin...
[ 1.064646] omap2-nand driver initializing
[ 1.069160] OneNAND driver initializing
[ 1.073707] Initializing USB Mass Storage driver...
[ 1.079008] usbcore: registered new interface driver usb-storage
[ 1.085327] USB Mass Storage support registered.
[ 1.092579] gadget: Mass Storage Function, version: 2009/09/11
[ 1.098873] gadget: Number of LUNs=1
[ 1.102729] lun0: LUN: removable file: (no medium)
[ 1.108195] gadget: android_usb ready
[ 1.112181] musb-hdrc musb-hdrc.0: MUSB HDRC host driver
[ 1.117810] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 1
[ 1.126359] hub 1-0:1.0: USB hub found
[ 1.130299] hub 1-0:1.0: 1 port detected
[ 1.134984] mousedev: PS/2 mouse device common for all mice
[ 1.142211] using rtc device, omap_rtc, for alarms
[ 1.147178] omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0
[ 1.154150] i2c /dev entries driver
[ 1.158808] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[ 1.165406] device-mapper: uevent: version 1.0.3
[ 1.170539] device-mapper: ioctl: 4.21.0-ioctl (2011-07-06) initialised: [email protected]
[ 1.179451] Bluetooth: HCI UART driver ver 2.2
[ 1.184127] Bluetooth: HCI H4 protocol initialized
[ 1.189182] Bluetooth: HCILL protocol initialized
[ 1.195616] usbcore: registered new interface driver usbhid
[ 1.201531] usbhid: USB HID core driver
[ 1.206376] logger: created 256K log 'log_main'
[ 1.211283] logger: created 256K log 'log_events'
[ 1.216403] logger: created 256K log 'log_radio'
[ 1.221387] logger: created 256K log 'log_system'
[ 1.227704] ALSA device list:
[ 1.230830] No soundcards found.
[ 1.234566] nf_conntrack version 0.5.0 (3957 buckets, 15828 max)
[ 1.241470] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.247248] TCP cubic registered
[ 1.250649] NET: Registered protocol family 17
[ 1.255915] Bluetooth: RFCOMM TTY layer initialized
[ 1.261065] Bluetooth: RFCOMM socket layer initialized
[ 1.266501] Bluetooth: RFCOMM ver 1.11
[ 1.270448] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 1.276055] Bluetooth: BNEP filters: protocol multicast
[ 1.281553] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.287991] Registering the dns_resolver key type
[ 1.293025] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[ 1.301128] ThumbEE CPU extension supported.
[ 1.306641] omap2_set_init_voltage: unable to get clk dpll1_ck
[ 1.312782] omap2_set_init_voltage: unable to set vdd_mpu_iva
[ 1.318872] omap2_set_init_voltage: unable to get clk l3_ick
[ 1.324825] omap2_set_init_voltage: unable to set vdd_core
[ 1.335992] omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[ 1.345192] Waiting 1sec before mounting root device...
[ 1.388966] mmc0: new high speed SD card at address 1234
[ 1.395193] mmcblk0: mmc0:1234 SA02G 1.85 GiB
[ 1.402371] mmcblk0: p1 p2 p3
[ 5.849550] kjournald starting. Commit interval 5 seconds
[ 6.098443] EXT3-fs (mmcblk0p2): using internal journal
[ 6.103949] EXT3-fs (mmcblk0p2): recovery complete
[ 6.112826] EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
[ 6.120345] VFS: Mounted root (ext3 filesystem) on device 179:2.
[ 6.127118] Freeing init memory: 208K
[ 6.275318] WL1271: BT Disable
[ 6.398124] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
# [ 10.689071] adb_open
[ 10.697969] warning: `dhcpcd' uses 32-bit capabilities (legacy support in use)
[ 12.577502] gadget: Gadget Zero, version: Cinco de Mayo 2008
[ 12.583581] gadget: zero ready
[ 12.586969] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
[ 12.592569] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 2
[ 12.601273] hub 2-0:1.0: USB hub found
[ 12.605215] hub 2-0:1.0: 1 port detected
[ 12.611683] android_usb: already disabled
[ 12.616818] adb_bind_config
[ 12.873918] Compat-wireless backport release: compat-wireless-2011-07-27
[ 12.881078] Backport based on wl12xx.git v2.6.39-1152-g0c08ddf
[ 14.435563] cfg80211: Calling CRDA to update world regulatory domain
[ 14.986609] cfg80211: World regulatory domain updated:
[ 14.992040] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 15.000889] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.009246] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.017592] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.025936] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.034268] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.543739] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 27.266181] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 35.315270] request_suspend_state: wakeup (3->0) at 35309564422 (2000-01-01 00:00:34.460223314 UTC)
[ 36.232291] request_suspend_state: wakeup (0->0) at 36226586089 (2000-01-01 00:00:35.377243523 UTC)
[ 36.257450] init: untracked pid 130 exited
[ 37.577927] omaplfb: OMAPLFB_Init: OMAPLFBInit failed
[ 41.526016] request_suspend_state: wakeup (0->0) at 41520311299 (2000-01-01 00:00:40.670970399 UTC)希望大神指明一个方向，我好去修改
这里有篇文章，也出现了OMAPLFBInit failed
和你相同的问题，他是刚开机的时候，就会出现你这个错误，然后按复位键(热启动)，就可以正常
解决办法是在复位电路上进行优化
UBOOT启动没
U-Boot SPL 2011.09-00001-g95a7849 (Feb 14 2012 - 10:53:14)
Texas Instruments Revision detection unimplemented
Could not probe the EEPROM; something fundamentally wrong on the I2C bus.
read_eeprom() failure
OMAP SD/MMC: 0
reading u-boot.img
reading u-boot.img
U-Boot 2011.09-00001-g95a7849 (Feb 14 2012 - 10:53:14)I2C: ready
DRAM: 256 MiB
WARNING: Caches not enabled
Could not probe the EEPROM; something fundamentally wrong on the I2C bus.
NAND: HW ECC Hamming Code selected
256 MiB
MMC: OMAP SD/MMC: 0
Net: cpsw
Hit any key to stop autoboot: 0
SD/MMC found on device 0
reading uEnv.txt226 bytes read
Loaded environment from uEnv.txt
Importing environment from mmc ...
Running uenvcmd ...
reading uImage2631064 bytes read
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-3.1.0-g62911f8-dirty
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2631000 Bytes = 2.5 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OKStarting kernel ...Uncompressing Linux... done, booting the kernel.
[ 0.000000] Linux version 3.1.0-g62911f8-dirty (root@ll-virtual-machine) (gcc version 4.4.3 (GCC) ) #1 Sun Sep 23 19:29:08 CST 2012
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: am335xevm
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] AM335X ES1.0 (neon )
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyO0,115200n8 androidboot.console=ttyO0 mem=256M root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait rootdelay=1 init=/init ip=off
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 253292k/253292k available, 8852k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffa00000 - 0xffe00000 ( 4 MB)
[ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc04b5000 (4788 kB)
[ 0.000000] .init : 0xc04b5000 - 0xc04e9000 ( 208 kB)
[ 0.000000] .data : 0xc04ea000 - 0xc0532fa0 ( 292 kB)
[ 0.000000] .bss : 0xc0532fdc - 0xc0669f48 (1244 kB)
[ 0.000000] NR_IRQS:396
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[ 0.000000] Total of 128 interrupts on 1 active controller
[ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz
[ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000263] Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464)
[ 0.058632] pid_max: default: 32768 minimum: 301
[ 0.058802] Security Framework initialized
[ 0.058889] Mount-cache hash table entries: 512
[ 0.059376] CPU: Testing write buffer coherency: ok
[ 0.064479] print_constraints: dummy:
[ 0.064735] NET: Registered protocol family 16
[ 0.064970] GPMC revision 6.0
[ 0.066047] OMAP GPIO hardware version 0.1
[ 0.066888] omap_l3_smx omap_l3_smx.0: couldn't find resource
[ 0.067009] omap_mux_init: Add partition: #1: core, flags: 0
[ 0.069765] omap_i2c.1: alias fck already exists
[ 0.070658] omap2_mcspi.1: alias fck already exists
[ 0.070796] omap2_mcspi.2: alias fck already exists
[ 0.080390] bio: create slab <bio-0> at 0
[ 0.081472] SCSI subsystem initialized
[ 0.082454] usbcore: registered new interface driver usbfs
[ 0.082582] usbcore: registered new interface driver hub
[ 0.082751] usbcore: registered new device driver usb
[ 0.083668] omap_i2c omap_i2c.1: bus 1 rev4.0 at 100 kHz
[ 0.084572] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.085236] Bluetooth: Core ver 2.16
这是前面的启动信息，uboot启动了，内核也没问题，看着fs也挂载上了，就是不知道哪里的问题